Hi, let's see if we can use images:
Hurray! I love riding my bike in Germany.
Worfje's Timeline 5th Gen
- Worfje
- Posts: 98
- Joined: Fri May 29, 2026 10:28 pm
- Location: Netherlands
- Has liked: 105 times
- Reiceved a like: 74 times
Worfje's Timeline 5th Gen
You do not have the required permissions to view the files attached to this post.
Last edited by Worfje on Sun Jun 07, 2026 10:26 am, edited 1 time in total.
- Worfje
- Posts: 98
- Joined: Fri May 29, 2026 10:28 pm
- Location: Netherlands
- Has liked: 105 times
- Reiceved a like: 74 times
As mentioned: bought the bike in 2006 2nd hand with 25000 km on it for 6250 euro and the first actual maintenance (besides oil/oil filter and refreshing cooling fluid) was a new chain (18th of March 2007):
You do not have the required permissions to view the files attached to this post.
Last edited by Worfje on Sun Jun 07, 2026 10:28 am, edited 6 times in total.
- Worfje
- Posts: 98
- Joined: Fri May 29, 2026 10:28 pm
- Location: Netherlands
- Has liked: 105 times
- Reiceved a like: 74 times
Performed valve clearance check at 9th of August 2007:
Only one value was just out of specification, namely cilinder 1, one of the exhaust ports with 40 um.
I trusted I made a measurement error and let it be.
Only one value was just out of specification, namely cilinder 1, one of the exhaust ports with 40 um.
I trusted I made a measurement error and let it be.
You do not have the required permissions to view the files attached to this post.
- Worfje
- Posts: 98
- Joined: Fri May 29, 2026 10:28 pm
- Location: Netherlands
- Has liked: 105 times
- Reiceved a like: 74 times
Installed a 'pro-oiler' on 26th March 2007 after a group buy organized by the Dutch VFR Owners Club, which I regretted (oil on rear tyre, no go) and I removed after a year or so:
You do not have the required permissions to view the files attached to this post.
- JZH
- Posts: 28
- Joined: Mon Jun 01, 2026 3:06 pm
- Location: Leiden, NL/London, UK
- Has liked: 30 times
- Reiceved a like: 39 times
- Contact:
LOL, I remember going through my own "chain oiler" phase... The UK-made Scottoilers were all the rage back in the late 1980s, so I put one on my first VFR750 in 1990. I had the brilliant idea of cutting out the rear mudguard to allow the number plate to sit flush over the Scottoiler. It rarely worked properly, and oil all over the rear of the bike and a hacked up rear mudguard was all I had to show for my efforts... (The Scottoiler used vacuum to open the valve.) Fun times.
Ciao,
JZH
Ciao,
JZH
Leiden, NL/London, UK
www.vsource.org
RS250; SXV550; CBR250RRR; CBR400RRN; RVF400RT; VFR400RL; VFR400RN; VFR750FL; VFR800FiY; VFR800Fi1; VFR750FP; ST1300A4 (and counting...)
"After all, what is a motorcycle for if it isn't action?"
www.vsource.org
RS250; SXV550; CBR250RRR; CBR400RRN; RVF400RT; VFR400RL; VFR400RN; VFR750FL; VFR800FiY; VFR800Fi1; VFR750FP; ST1300A4 (and counting...)
"After all, what is a motorcycle for if it isn't action?"
Have a cameleon brand on my’86, works quite well. They sell on eBay.ca & aren’t cheap, mine has been good for a dozen seasons & is very helpful in wet conditions. Will dirty white wheel but not terrible unless you adjust to run wide open flow rate 
- Worfje
- Posts: 98
- Joined: Fri May 29, 2026 10:28 pm
- Location: Netherlands
- Has liked: 105 times
- Reiceved a like: 74 times
Demounted the fork tubes for their first service (under my care) around March 2008:
In my experience, a bit of an achilles of the VFR800 (5th gen). Quickly rusts due to damaged chrome layer due to road debris and probably also correlating with the 'sweating' of suspension fluid.
In my experience, a bit of an achilles of the VFR800 (5th gen). Quickly rusts due to damaged chrome layer due to road debris and probably also correlating with the 'sweating' of suspension fluid.
You do not have the required permissions to view the files attached to this post.
- Worfje
- Posts: 98
- Joined: Fri May 29, 2026 10:28 pm
- Location: Netherlands
- Has liked: 105 times
- Reiceved a like: 74 times
Rear shock gave up on April 2007:
I forgot which company was so kind to fix it and add a nitrogen(?) filling point.
I forgot which company was so kind to fix it and add a nitrogen(?) filling point.
You do not have the required permissions to view the files attached to this post.